OneUp Components

The EDC Pump offers a unique storage solution integrated into a high volume pump. It is designed to integrate with the EDC Tool System, CO2 canister or your favorite stash. Crafted from aluminum with a durable textured machined finish.

--

The EDC Pump offers a unique storage solution integrated into a high volume pump. It is designed to integrate with the EDC Tool System, CO2 canister or your favorite stash. Crafted from aluminum with a durable textured machined finish.

 

PUMP VOLUME

A mini pump might look appealing, but with typical volumes of 30-60cc it will take hundreds of strokes to inflate a new tube and has absolutely no chance of re-inflating a tubeless setup. When you get a flat, you want to fix it as fast as possible as riding time is precious. At 100cc and at 160g our high volume pump has the highest volume to weight ratio on the market.

 

FAST-ON HEAD

Firmly push the pump head onto the Presta valve until it bottoms out, then pump. With our fast-on head the valve stem is securely supported so there's no chance of bending, breaking or unseating the valve and no chance of unscrewing your valve core when you remove the pump.

 

EDC PUMP SPEC

• 2 Sizes: High Volume 100cc & Compact 70cc
  
  
  • 1-1/4" dia x 7" for 70cc (32mm dia x 178mm)
  
  
  • 1-1/4" dia x 10" for 100cc (32mm dia x 254mm)
  
  
  

• 100cc Pump holds EDC Tool & a 20g CO2 or EDC Tool & the Storage Capsule

• 70cc Pump holds  EDC Tool (no Storage Capsule) or a 20g CO2

• Fast-On Head (Presta Only) - No threads or locking levers

• Integrated CO2 Inflator

• Fully Sealed, Weatherproofed Internals

• Includes Bottle Cage Mount

Material: 6061-T6

Weight: 135g - 70cc, 160g - 100cc (without EDC tool system)

Colour: Black

Patents Pending

Inflator Instruction

The OneUp Aluminum Pedals features a huge (115x105mm) super grippy platform with 10 rear-loading hexagonal steel pins per side to keep your feet planted on even the roughest of trails. With a weight of only 365g, the OneUp Aluminum Pedals won't slow you down on the climbs.

Designed from stealth rubber down and shaped with a subtle convex profile to provide you with more grip thanks to the pedals sitting in the natural arch of your foot. The ultra-thin design (only 8mm at the leading edge) gives you maximum clearance to reduce pedal strikes and deflect off trail obstacle. Clip Less, Ride More.

The EDC Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer.

--

The EDC Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer.

Top caps are compatible with all 1-1/8" aluminum steerer tubes.

The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes.

Check fork compatibility.

 

KIT INCLUDES

• EDC TOP CAP

• EDC steerer plug

• 2x 1mm, 3mm, & 5mm Headset Spacers

 

INSTALL THE EDC TOP CAP

 

1. You need a minimum of 5mm of headset spacer above the stem and your steerer tube should be 1-2mm below the top of this spacer.

1. Apply a small amount of grease to your newly cut thread and screw in your new EDC top cap.

1. The Top Cap interface uses a standard cassette lockring tool. You do not need to apply much torque as you are only preloading the bearings. (Your stem pinch bolts are what holds your fork in place). The EDC multitool contains a top cap tightening tool. So even when riding you always have the ability to tighten your headset if need be.

1. Align your stem and tighten your stem bolts to the manufacturers recommended torque.

1. The final step is to insert the plastic bung/plug into the bottom of your fork. Turn your 8mm hex sideways and use it to push the plug into the fork by pulling the 8mm towards your chest. This piece holds the bottom of the EDC Tool and stops it from rattling. It also keeps dirt out of your fork and has a small drain hole.

Note* The EDC Tap kit includes a star nut puller and self aligning tap

Patents Pending

All compatibility and fit determinations have been made solely by OneUp. Use of this or any other aftermarket product may void any warranty you have with the original part manufacturer.

A low profile single lock on grip, designed to reduce arm pump and hand numbness. The Diamond knurled texture, with saw tooth finger ramps and a super tacky 20A compound provide ultimate traction. More traction means less death-gripping the bars and less arm pump. Our single lock has the profile of your favorite double lock-on. But to reduce hand numbness we've replaced the hard outer clamp with extra rubber for greater cushioning of your palm heel. Get all the benefits of an “ergonomic” grip without the city bike cruiser look!

SPECS